SomaticView™ Version 1.0 User's Guide Technology that counts
Table of contents viii This page was intentionally left blank
1 Installation 11 Installation When the NucleoCounter SCC-100 is connected to a computer running SomaticView it is possible to register the estimate
1 Installation 2 Figure Figure Figure Figure 1111 The Found New Hardware Wizard. The driver needed is supplied on the NucleoCounter SCC-100 CD-ROM.
1 Installation 3 Figure Figure Figure Figure 3333 Locations where the computer searches for the driver for the NucleoCounter SCC-100. Make sure that
1 Installation 4 Figure Figure Figure Figure 5555 The installation has been successful. If the installation was successful the dialogue in figure 5
1 Installation 5For the installation of SomaticView insert the NucleoCounter SCC-100 CD-ROM into the computer. To start the installation, locate the
1 Installation 6In the next dialogue Figure 8, please confirm the default destination folder for installation of the LabVIEW Run-Time Engine by click
1 Installation 7If the installation is successful the dialogue shown in figure 10 will appear. Click “Finish” to complete the installation. The Somat
1 Installation 8 Figure Figure Figure Figure 11111111 “System Properties” dialogue. In the “System Properties” dialogue select the “Hardware” tag (f
1 Installation 9Highlight the “nucleo Device” as shown in figure 12 and option-click it using the right mouse button. This activates a pop-up menu. S
This page was intentionally left blank
1 Installation 10 This page was intentionally left blank
2 Getting started with SomaticViewTM 112 Getting started with SomaticViewTM SomaticView allows the user to register the results of counting of Somat
2 Getting started with SomaticViewTM 12 This page was intentionally left blank
3 The structure of SomaticViewTM 133 The structure of SomaticViewTM SomaticView is operated through a number of tabs. The different tabs are selecte
4 Analysis tab 144 Analysis tab Analysis is the default start-up tab of SomaticView. In this tab data and results transferred from the NucleoCounter
4 Analysis tab 154.2 Folder selection. Each day SomaticView is launched, a new session (folder) is created. The folder’s name is the date of the ses
4 Analysis tab 163. Click “Select Cur Dir” and the session will be displayed in SomaticView. The files will appear in the file list2 and it is possi
4 Analysis tab 17 Figure Figure Figure Figure 19191919 SomaticView presents the images from the NucleoCounter SCC-100 like a starry sky. Each “star”
4 Analysis tab 18 This page was intentionally left blank
5 Utility tab 195 Utility tab In the Utility tab (figure 20) it is possible to print and save results. Furthermore it is possible to select language
i SomaticView™ A part of the NucleoCounter® SCC-100™systemManual No. 991-0201 (English)Version 1.0March 25, 2004
5 Utility tab 20If no folder is selected SomaticView suggest that the folder from today is selected. Figure Figure Figure Figure 22222222 Accept
5 Utility tab 21ChemoMetec A/S will implement new languages. Please contact ChemoMetec A/S NucleoCounter SCC-100 Technical Support on the address inf
5 Utility tab 22Either WordPad or Notepad3 can be configured as text editors. Therefore, if it is not possible to locate “wordpad.exe”, then: a. Sel
5 Utility tab 232. Choose the location to save the file to be the SomaticView folder (usually C:\SomaticView). 3. In the bottom of the dialogue cha
5 Utility tab 247. Exit WordPad. 5.4.2 Define font for Notepad Similarly Notepad can be set up for SomaticView, follow the directions below. 1.
6 Troubleshooting 256 Troubleshooting Occasionally difficulties with the SomaticView software may occur. In the following a short description and su
6 Troubleshooting 26 Figure Figure Figure Figure 33333333 Input open failure Input open failure Input open failure Input open failure Figure Figu
6 Troubleshooting 27SomaticView is activated. If the “QUIT”-button does not respond (after only few seconds), you can close SomaticView down using th
6 Troubleshooting 28 This page was intentionally left blank
7 Technical specifications 297 Technical specifications 7.1 SomaticView™ software System requirements For operating systems see table 1 below.
ii This page was intentionally left blank
7 Technical specifications 30 This page was intentionally left blank
8 Appendix 1: Printed report list 318 Appendix 1: Printed report list Below is an example of what the printed and saved report list looks like
8 Appendix 1: Printed report list 32 This page was intentionally left blank
339 Index A Analysis tab ...14 B Browse files from active session ...15 Browse stored files...
iiiCustomerCustomerCustomerCustomer support support support support If you have questions about installing or using your SomaticViewTM software c
iv This page was intentionally left blank
Intended use vIntended useIntended useIntended useIntended use The SomaticView™ software is intended to be used with the NucleoCounter® SCC-100™ i
Intended use vi This page was intentionally left blank
Table of contents viiTable of contentsTable of contentsTable of contentsTable of contents 1 INSTALLATION...........
Comments to this Manuals